Samsung Galaxy S6 Edge Front Facing Camera Replacement - Samsung Galaxy S6 Edge

Step 1 | SIM Tray

Never insert the tool into the microphone hole — risk of damage.

Insert a paper clip or SIM eject tool into the SIM card slot's hole on top of the phone.
Press to eject the SIM tray.
Remove the SIM tray from the phone.

Step 2 | iOpener Heating

Any debris on the bottom of the microwave may adhere to the iOpener.

Place the iOpener in the center of the microwave.

For carousel microwaves: Ensure the plate spins freely to prevent overheating and burning the iOpener.

Step 3

Never touch a swollen iOpener to avoid burns.

Heat the iOpener in the microwave for thirty seconds.
Note: Time may vary depending on your microwave's wattage.
The iOpener is ready when it's almost too hot to touch.

Do not overheat the iOpener, as this can cause it to burst.

Reheat for an additional thirty seconds if the iOpener cools during the repair.

Do not exceed 100 ̊C (212 ̊F) when heating the iOpener.

A properly heated iOpener should stay warm for up to ten minutes.
Continue using a hot iOpener while waiting for it to cool down further if needed.

Step 4

Be cautious when handling the extremely hot iOpener after microwave use.

Hold the iOpener by one of its flat ends to avoid contact with the hot center.
Wear an oven mitt if you need extra protection when handling the iOpener.

Step 5 | Alternate iOpener heating method

Be cautious of extreme temperatures — handle the hot iOpener carefully.

Fill a pot or pan with enough boiling water to fully submerge an iOpener.
Turn off heat after bringing water to a boil.
Soak an iOpener in the hot water for 2-3 minutes, ensuring it's fully submerged.
Use tongs to carefully extract and dry the heated iOpener with a towel.
Reheat as needed by following these steps.

Step 6 | Rear Glass

Opening your phone will compromise its waterproof seals. Have replacement adhesive ready before proceeding.

Careful: If reassembling without replacing adhesive, avoid liquid exposure.

For shattered glass, cover with packing tape to hold together during removal.

Lay the heated iOpener over the rear panel for about two minutes to loosen edge adhesive.

Avoid overheating: Reheat and reapply as needed according to the iOpener instructions.

Shift the iOpener to heat remaining panel area for another two minutes.

Caution: Alternative heating methods (hair dryer, heat gun, hot plate) risk damage to OLED display and internal battery; use with care.

Step 7

Apply a suction cup near the bottom edge of the rear glass when it's hot.

Lift on the suction cup to create a small gap underneath the glass.
Insert an opening pick into the gap.

Optionally, add a few drops of isopropyl alcohol for extra adhesive weakening.

Step 8

Slide the pick along the bottom edge of the phone to slice through the adhesive securing the rear glass.

If necessary, re-heat the rear glass to prevent the glue from cooling and hardening.
Leave the pick in place for the next step or insert a second pick to maintain tension on the separated glue.

Avoid allowing the glue to cool and re-adhere, as it may require re-heating to separate again.

Step 9

Continue the heating and cutting process for the remaining three edges.

Apply a separate opening pick to each edge, ensuring the adhesive doesn't reseal.

Step 10

Use an opening pick to slice through any remaining adhesive.

Remove the rear glass.

Step 11

Ensure all adhesives are completely removed before installing new rear glass.

Use tweezers to remove any remaining adhesive from the phone's chassis.
Clean adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth, swiping in one direction only.

Install new rear glass by peeling off backing and carefully aligning one edge against the phone's chassis. Firmly press the glass into place.

Step 12 | Midframe Assembly

Remove the thirteen 3.3 mm Phillips #00 screws from the midframe.

Step 13

Apply pressure to the rear of the battery.
Lift upwards at the midframe's edges.

Step 14 | Front Facing Camera

Disconnect the front-facing camera from the motherboard using a spudger.

Remove the front-facing camera once disconnected.