LG Grace Motherboard Replacement

Never attempt to diagnose or repair an LG Grace smartphone (LGL59BL) without proper training and equipment. The motherboard is a critical component responsible for most phone functions, making diagnosis challenging.

Power off the device and have it inspected by a professional before proceeding with any repairs.
Motherboard replacement requires no special skills, but be aware that removal of the battery is involved.

Replacing the motherboard may not be cost-effective, as new phones with similar specs are available. However, doing so can help reduce electronic waste.

Remove the battery by carefully prying it loose (be cautious of a swollen battery that could rupture).
Once the battery is removed, proceed with the motherboard replacement process as outlined in this guide.

उचित प्रशिक्षण और उपकरणों के बिना कभी भी LG ग्रेस स्मार्टफोन (LGएल59बीएल) का निदान या मरम्मत करने का प्रयास न करें।

Motherboard अधिकांश फोन कार्यों के लिए जिम्मेदार एक महत्वपूर्ण घटक है, जिससे निदान चुनौतीपूर्ण हो जाता है।

किसी भी मरम्मत के लिए आगे बढ़ने से पहले उपकरण को बंद कर दें और किसी पेशेवर द्वारा इसका निरीक्षण करवा लें।

Motherboard प्रतिस्थापन के लिए किसी विशेष कौशल की आवश्यकता नहीं है, लेकिन ध्यान रखें कि Battery को हटाने में शामिल है।

Motherboard को बदलना लागत प्रभावी नहीं हो सकता है, क्योंकि समान विनिर्देशों वाले नए फोन उपलब्ध हैं।

हालांकि, ऐसा करने से इलेक्ट्रॉनिक अपशिष्ट को कम करने में मदद मिल सकती है।

Battery को सावधानीपूर्वक खोलकर हटा दें (सूजी हुई Battery से सावधान रहें जो फट सकती है)।

एक बार Battery हट जाने के बाद, इस गाइड में उल्लिखित Motherboard प्रतिस्थापन प्रक्रिया के साथ आगे बढ़ें।

Step 1 | Phone Assembly

Risk of damage to the phone or injury to yourself.

Locate the small gap along the edge of the phone's back.
Pry open the gap with your fingernail.
If you have short nails, a pry tool can be used for assistance.

Step 2

Remove the battery from the rear of the device.

Pry the battery out using the small indent provided or by striking the back of the phone gently against a flat surface, such as a palm.

Step 3

Remove the M1.3 x 3mm screws from the back panel using a #00 Phillips screwdriver.

There should be 11 screws in total.

Step 4

Insert the Jimmy into the small gap between the phone screen and body.

Pry gently until the body pops loose.
Remove the Jimmy and use your hands to slowly pry the body away from the screen.

Step 5 | Rear Camera

Locate the pin connection marked by a red box in the guide image.

Gently lift the camera upwards and pull away from the connection.
The camera should detach with minimal effort.

Step 6 | Motherboard

Disconnect the front speaker from the motherboard.

The speaker's location is shown in the guide photo.
Gently pull the ribbon wire away from its connector to release it.

Step 7

Identify and disconnect the ribbon cable attached near the charging port.

Pull the ribbon cable away from its connection, similar to previous steps.
The motherboard should now be completely free.

Step 8

Hold the phone firmly in one hand.

Gently grasp the motherboard's edge near the ports.
Lift the motherboard away from the screen assembly using your first hand.