Home Repair Guides Google Pixel Google Pixel 9 Pro Fold Google Pixel 9 Pro Fold Outer Front Camera Replacement

Google Pixel 9 Pro Fold Outer Front Camera Replacement

This repair guide, created by iFixit's team, is not sponsored or approved by Google. For more information on our repair guides, visit our website.

  • Replace the outer front camera module in your Google Pixel 9 Pro Fold using this guide.

Step 1 | Prepare your phone for disassembly

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 1: Prepare your phone for disassembly

Allow the battery to discharge below 25% to prevent potential fires.

  • Disconnect all cables from your device.
  • Power down your phone completely.

Step 2 | Insert an opening pick

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 2: Insert an opening pick
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 2: Insert an opening pick Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 2: Insert an opening pick Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 2: Insert an opening pick Thumbnail 3

Apply suction cup near bottom edge of screen for maximum adhesion.

To avoid damaging the screen, use strong, steady force when pulling up on suction cup.

  • Insert an opening pick into gap created by suction cup.
  • If screen is badly cracked, cover with clear packing tape for better adhesion.
  • Alternatively, use very strong tape instead of suction cup or superglue to screen if needed.

Step 3 | Separate the adhesive

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 3: Separate the adhesive
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 3: Separate the adhesive Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 3: Separate the adhesive Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 3: Separate the adhesive Thumbnail 3

Do not insert the opening pick deeper than 3 mm.

  • You may choose to mark your opening pick at 3 mm from the tip for reference.
  • Slide the opening pick around the bottom right corner and up the right edge of the screen.

Step 4

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 4
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 4 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 4 Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 4 Thumbnail 3

Place the pick at the top right corner and slide it towards the front, stopping just before the camera lens.

Step 5

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 5
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 5 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 5 Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 5 Thumbnail 3

Remove the opening pick almost entirely, leaving just a small portion under the screen.

  • Slide the remaining part of the pick across the top edge of the screen, passing over the front camera.
  • Return the pick to its original depth before proceeding further.

Step 6

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 6
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 6 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 6 Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 6 Thumbnail 3

Risk of damage to display cable if pick is slid too far.

  • Insert the opening pick into the top left corner of the screen.
  • Stop the pick at two-thirds down the left edge and do not proceed further.

Step 7

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 7
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 7 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 7 Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 7 Thumbnail 3

Insert the opening pick into the lower-left corner of the device.

  • Hold the pick at a 90-degree angle to the screen.
  • Pull the pick outwards until it reaches a depth of approximately 2 mm.
  • Rotate the pick clockwise around the bottom left corner, applying gentle pressure.

Step 8

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 8
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 8 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 8 Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 8 Thumbnail 3

Don't fully remove the screen yet as it's still connected to the phone by a cable.

Be careful not to damage the screen or surrounding components when handling.

  • Free the screen from the frame, using an opening pick if there's remaining adhesive around the edges.
  • Lift the right edge of the screen and swing it over the left edge of the phone.
  • Prop up the screen with your suction handle or a clean, sturdy object to maintain its position.

Step 9 | Remove the display cable bracket screw

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 9: Remove the display cable bracket screw
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 9: Remove the display cable bracket screw Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 9: Remove the display cable bracket screw Thumbnail 2

Keep track of each screw during this repair to ensure correct reinstallation.

  • Use either Torx or Torx Plus bits (T3 or T4) for screws, noting that one size larger is acceptable.
  • Apply constant downward force when using Torx or Torx Plus bits to avoid stripping the screw head.

Be careful not to strip screws when applying force.

  • Use a Torx Plus 3IP driver to remove the 2.2 mm-long screw securing the display cable bracket.

Step 10

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 10
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 10 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 10 Thumbnail 2

Apply conductive tape to secure the display cable bracket to the frame.

  • Lift the display cable bracket using a spudger or your fingers, and gain access to the press connector underneath.

Step 11 | Disconnect the display cable

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 11: Disconnect the display cable
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 11: Disconnect the display cable Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 11: Disconnect the display cable Thumbnail 2

Insert the pointed end of a spudger into the display cable press connector.

  • Gently pry up on the connector using the spudger's point.
  • The connector should release and come free from the motherboard.

Step 12 | Remove the screen

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 12: Remove the screen

Remove the screen from its housing by lifting it straight up.

Step 13 | Remove the battery bracket screw

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 13: Remove the battery bracket screw
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 13: Remove the battery bracket screw Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 13: Remove the battery bracket screw Thumbnail 2

Remove the Torx Plus 3IP driver and use it to take out the 2.0 mm-long screw holding the battery bracket in place.

Step 14 | Disconnect the battery

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 14: Disconnect the battery
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 14: Disconnect the battery Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 14: Disconnect the battery Thumbnail 2

Secure the battery connector bracket with conductive tape to the lower board.

  • Use tweezers or your fingers to move the battery bracket away from the battery press connector.

Step 15

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 15
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 15 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 15 Thumbnail 2

Use the point of a spudger to pry up and release the battery press connector.

Step 16 | Remove the rubber block

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 16: Remove the rubber block
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 16: Remove the rubber block Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 16: Remove the rubber block Thumbnail 2

Use tweezers, or your fingers, to remove the rubber block covering a screw on the top board.

Step 17 | Remove the top interconnect cable bracket screws

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 17: Remove the top interconnect cable bracket screws
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 17: Remove the top interconnect cable bracket screws Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 17: Remove the top interconnect cable bracket screws Thumbnail 2

Remove the Torx Plus 3IP driver with a 2.5 mm bit and unscrew the screws that secure the top interconnect cable bracket.

  • The screws are located at each end of the bracket.

Step 18 | Remove the top interconnect cable bracket

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 18: Remove the top interconnect cable bracket
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 18: Remove the top interconnect cable bracket Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 18: Remove the top interconnect cable bracket Thumbnail 2

Remove the top interconnect cable bracket using tweezers or your fingers.

Step 19 | Disconnect the top interconnect cable

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 19: Disconnect the top interconnect cable
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 19: Disconnect the top interconnect cable Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 19: Disconnect the top interconnect cable Thumbnail 2
  • Position the spudger tip under the top right corner of the top interconnect cable press connector, just above the golden marker.
  • Pry up to release and then disconnect the top interconnect cable press connector.

Step 20 | Remove the top board screw

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 20: Remove the top board screw
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 20: Remove the top board screw Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 20: Remove the top board screw Thumbnail 2
  • Remove the top board by using a Torx Plus 3IP driver to loosen the single screw.

Step 21 | Remove the top board

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 21: Remove the top board
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 21: Remove the top board Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 21: Remove the top board Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 21: Remove the top board Thumbnail 3

Be careful not to puncture or deform the battery.

  • Insert the flat end of a spudger under the bottom edge of the top board.
  • Twist the spudger to lift the top board and unclip it from the frame.
  • Remove the top board.

Step 22 | Remove the outer front camera

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 22: Remove the outer front camera
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 22: Remove the outer front camera Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 22: Remove the outer front camera Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 22: Remove the outer front camera Thumbnail 3

Avoid applying excessive pressure on the top board.

  • Insert a spudger under the top right corner of the front camera press connector, next to the golden marker.
  • Do not insert the spudger elsewhere, as it may dislodge surface-mounted components.

  • Pry up and disconnect the outer front camera.

Step 23 | End of disassembly

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 23: End of disassembly

Reassembly instructions begin here.

  • Follow these steps in reverse order from the previous disassembly instructions.

Step 24 | Reconnect the outer front camera

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 24: Reconnect the outer front camera
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 24: Reconnect the outer front camera Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 24: Reconnect the outer front camera Thumbnail 2

Pinch the outer front camera press connector into its socket on the top board using your fingers.

Step 25 | Reinstall the top board

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 25: Reinstall the top board
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 25: Reinstall the top board Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 25: Reinstall the top board Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 25: Reinstall the top board Thumbnail 3

Hold the top board at a 45-degree angle and press it firmly against the until the metal spring clicks into place.

  • Make sure not to press too hard, which could damage the board or the frame.

  • Press the board flat to ensure proper alignment of the screw holes.

Step 26

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 26
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 26 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 26 Thumbnail 2
  • Install the Torx Plus 3IP driver for the job.
  • Secure the top board with a 2.2 mm-long screw.

Step 27 | Reconnect the top interconnect cable

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 27: Reconnect the top interconnect cable

Press the top interconnect cable connector firmly into place.

Step 28 | Reinstall the top interconnect cable bracket

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 28: Reinstall the top interconnect cable bracket
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 28: Reinstall the top interconnect cable bracket Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 28: Reinstall the top interconnect cable bracket Thumbnail 2

Align the screw holes of the top interconnect cable bracket with the top board.

  • Position the bracket on the board, ensuring proper alignment.
  • Secure the bracket by fastening it to the board using the aligned screw holes.

Step 29

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 29
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 29 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 29 Thumbnail 2

Install the Torx Plus 3IP driver and screw in the two 2.2 mm-long screws securing the top interconnect cable bracket.

Step 30 | Reinstall the rubber block

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 30: Reinstall the rubber block
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 30: Reinstall the rubber block Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 30: Reinstall the rubber block Thumbnail 2

Position the rubber block onto its designated location on the top board.

  • Press the rubber block firmly into place.

Step 31 | Reconnect the flip battery

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 31: Reconnect the flip battery

Reconnect the flip battery press connector.

Step 32 | Reinstall the flip battery bracket

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 32: Reinstall the flip battery bracket
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 32: Reinstall the flip battery bracket Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 32: Reinstall the flip battery bracket Thumbnail 2

Position the flip battery bracket over the press connector, ensuring the screw holes are aligned.

Step 33

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 33
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 33 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 33 Thumbnail 2

Insert the Torx Plus 3IP driver and tighten the battery bracket screw, which is 2.0 mm long.

Step 34 | Remove the old adhesive

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 34: Remove the old adhesive
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 34: Remove the old adhesive Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 34: Remove the old adhesive Thumbnail 2

Old adhesive residue can damage new components.

  • Remove the old bottom left outer screen adhesive using a spudger or your fingers.
  • Mix isopropyl alcohol (>90%) with a coffee filter or a .
  • Clean any remaining adhesive residue from the area.
  • Ensure all surfaces are free of old adhesive before proceeding.

Step 35 | Compare your new adhesive

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 35: Compare your new adhesive
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 35: Compare your new adhesive Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 35: Compare your new adhesive Thumbnail 2

Check that the bottom left outer screen adhesive is properly aligned with the frame.

  • The clear liner should be facing the frame.

Step 36 | Apply the new adhesive

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 36: Apply the new adhesive
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 36: Apply the new adhesive Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 36: Apply the new adhesive Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 36: Apply the new adhesive Thumbnail 3

Remove the clear liner from the bottom left outer screen adhesive.

  • Place the exposed adhesive onto the frame.

Step 37

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 37
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 37 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 37 Thumbnail 2

Press the adhesive strip firmly onto the frame using the flat end of a spudger.

Step 38 | Apply the new adhesive

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 38: Apply the new adhesive
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 38: Apply the new adhesive Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 38: Apply the new adhesive Thumbnail 2

Verify that the perimeter outer screen adhesive aligns with the frame.

  • The clear liner must be positioned facing inward, toward the frame.

Step 39

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 39
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 39 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 39 Thumbnail 2

Work slowly when handling the new adhesive strip to avoid applying it incorrectly.

  • Pry away the top half of the adhesive strip from its clear liner.
  • Keep the peeled half folded while working with it.

Step 40

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 40
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 40 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 40 Thumbnail 2

Position the adhesive with its top edge aligned to the centerline of the frame.

  • Use the frame's corner points as reference for alignment.
  • Press the adhesive firmly onto the frame.

Step 41

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 41
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 41 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 41 Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 41 Thumbnail 3

Press the top edge of the adhesive against the frame using the flat end of a spudger or your fingers.

Step 42

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 42
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 42 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 42 Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 42 Thumbnail 3

Slowly place the remaining adhesive along the phone's edge.

Avoid applying excessive pressure to avoid air bubbles or creasing.

Step 43

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 43
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 43 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 43 Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 43 Thumbnail 3

Press the remaining adhesive firmly onto the frame using the flat end of a spudger or your fingers.

Step 44

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 44
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 44 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 44 Thumbnail 2

Insert the tip of a spudger into the segmented tab at the bottom left corner of the large blue liner and gently pry it open.

Step 45

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 45
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 45 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 45 Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 45 Thumbnail 3

Remove the large blue liner by lifting the tab.

  • If any adhesive comes up with the liner, press it back down on the frame.
  • Use a spudger to secure the adhesive in place.

Step 46 | Reconnect the outer screen

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 46: Reconnect the outer screen
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 46: Reconnect the outer screen Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 46: Reconnect the outer screen Thumbnail 2

Support the screen with your hand or prop it up against a stable object.

  • Reconnect the outer screen cable press connector.

Step 47 | Reinstall the outer screen cable bracket

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 47: Reinstall the outer screen cable bracket
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 47: Reinstall the outer screen cable bracket Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 47: Reinstall the outer screen cable bracket Thumbnail 2

Align the outer screen cable bracket clip's screw hole with the frame.

  • Slide the clip back into place underneath the frame.

Step 48

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 48
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 48 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 48 Thumbnail 2

Install the Torx Plus 3IP drive for securing the display cable bracket.

  • Secure with a 2.2mm-long screw.

Step 49 | Expose the adhesive

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 49: Expose the adhesive
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 49: Expose the adhesive Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 49: Expose the adhesive Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 49: Expose the adhesive Thumbnail 3

Remove the blue liner from the bottom left outer screen adhesive strip.

  • Hold the screen above the frame and then separate one of the secondary liner's pull tabs at the bottom left corner.

Step 50

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 50
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 50 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 50 Thumbnail 2
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 50 Thumbnail 3

Peel off the secondary liner, exposing the adhesive.

If adhesive peels with liner, gently lay it back and secure with a spudger.

Step 51 | Secure the outer screen

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 51: Secure the outer screen
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 51: Secure the outer screen Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 51: Secure the outer screen Thumbnail 2

Align the outer screen with the frame, then press it firmly into position.

Step 52

Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 52
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 52 Thumbnail 1
Google Pixel 9 Pro Fold Outer Front Camera Replacement - Step 52 Thumbnail 2

Press the outer screen along its perimeter to attach it to the frame.

  • Apply light heat with a hair dryer or heat gun to reinforce bonding at edges, if desired.
  • Allow phone to sit for several hours for adhesive curing.
Check COD Availability

Enter your pincode to see if Cash on Delivery is available in your area.

Please enter a valid 6-digit pincode
S
Sakshi • Support
Online • replies in a few seconds
Hi there! I am Sakshi from the Sahii support team. I can help with active orders, live tracking, wallet questions, and genuine mobile spare parts. What would you like me to check?
Sakshi is checking this
filename.jpg