Google Pixel 2 XL Charging Assembly Replacement

Insert a SIM card eject tool or a straightened paperclip into the SIM card tray's release slot, situated on the left edge of the phone.

• Press firmly until the tray is fully ejected.

Remove the SIM card tray from the phone.

• The SIM card will fall out of the tray easily.
• When reinserting the SIM card, ensure it is in the correct orientation relative to the SIM card tray.

Apply clear tape over cracked display glass to prevent bodily harm and further breakage.

• Apply the tape for a smooth surface when using the suction cup.
• Place the suction cup near the SIM slot edge, avoiding the curved part of the glass.
• The curved portion may not provide a secure seal for the suction cup.

Apply firm, constant pressure with the suction cup for extended periods, or use a iOpener, heat gun, or hair dryer to loosen the adhesive.

• Pull up on the suction cup while inserting an opening pick between the front panel and rear case.
• If necessary, gently rock the suction cup and screen to further weaken the adhesive.

Avoiding damage to the phone's components is critical in this repair.

• Insert the pick no more than 0.25 inches (6 mm) into the bottom edge of the phone.
• Avoid touching the folded portion of the OLED panel, as it can damage the display.
• Do not cut along the left edge, as delicate display cables may be damaged.
• In the upper left corner, make very shallow cuts to avoid damaging the front-facing camera.

Insert the opening pick on the right side of the phone and gently slide it down.

• The goal is to start separating the display adhesive.

Use the flat edge of the opening pick, not the corner, to prevent it from being inserted too far.

• Slide the opening pick around the lower-right corner.
• Continue along the bottom edge of the phone.

Slide the pick along the top edge and around the top-right corner of the phone.

Hold the display from the right side and gently lift it, opening the phone like a book.

If the display resists, apply gentle prying to separate any remaining adhesive.

• The display is not yet fully detached due to fragile ribbon cables connecting it to the motherboard.
• Lay the display flat beside the phone on a table, keeping it close to avoid straining the cables.

Use a precision opener to pry up the lower edge of the digitizer cable connector cover.

Pry carefully to avoid damaging the cable underneath or losing the cover.

• Remove the clip on the bottom edge that secures the cover.
• Take care to keep the connector cover for reassembly.

Use the point of a spudger to lift the digitizer cable connector up and out of its socket on the motherboard.

• To re-attach press connectors, carefully align and press down on one side until it clicks into place, then repeat on the other side.

• Do not press down in the middle.

  Misaligned pins can bend, causing permanent damage.

If any part of your screen doesn't respond to touch after repair, re-seat this connector, ensuring it clicks fully into place and check for dust or obstructions in the socket.

Remove all adhesive tape from the display connector cover using tweezers.

Insert the point of a spudger into the small hole on the edge of the display connector cover.

• Pry the cover out of its recess using the spudger.
• Remove the connector cover and set it aside for reinstallation during reassembly.

Use a flat spudger to carefully lift the display cable connector out of its socket.

• Remove the display.

If replacing adhesive during reassembly, pause and proceed with that step now.

Remove the 11 x 3.8 mm Phillips screws securing the midframe.

Keep track of each screw to ensure proper reinstallation.

Use a prying tool to gently lift the midframe at the volume button area.

• Insert the tool into the notch near the volume buttons.
• Pry the midframe upwards and away from the phone.

Be careful not to damage any surrounding components.

Remove the midframe.

Disconnect the battery connector using the flat end of a spudger.

Use the pointed end of a spudger to carefully release the front-facing camera connector.

• Attach the front camera to the motherboard first.
• Insert the motherboard after securing the front camera.

Locate and carefully disconnect the right Active Edge sensor connector using the flat end of a spudger.

Beware of bent or pinched cables.

• Next, detach the antenna cable from its socket.

Disconnect the fingerprint sensor connector with the pointed end of a spudger.

Disconnect the left Active Edge sensor connector using the flat end of a spudger.

Disconnect the charging assembly connector with the flat end of a spudger.

Disconnect the front-facing sensor assembly connector using the pointed end of a spudger.

Clear all cables and connectors from the board.

• Use a spudger to gently lift the motherboard's bottom edge.
• If it starts to bend, stop and check for any obstruction.

Be careful not to damage the narrow part of the motherboard.

Lift the board out by sliding it toward the bottom while holding near the SIM card slot.

Remove the motherboard.

Keep the phone flat with battery facing up to avoid camera fall-out.

• Reinstall motherboard, moving cables and connectors clear of the board.
• Ensure all connectors align with their sockets.

Slide the point of a spudger under the lower left side of the loudspeaker.

• Slowly pry the speaker assembly up from the phone.
• If having trouble, insert the flat end of a spudger into the gap at the base of the phone and slowly pry up.

Remove the loudspeaker from the phone.

Disconnect the white antenna cable located to the right of the battery using the pointed end of a spudger.

Apply heat to the bottom of the back of the phone using a hair dryer, heat gun, or an iOpener for approximately 1 minute.

• The goal is to soften the adhesive securing the charging assembly.

Slide an opening pick under the charging assembly flex cable on the left side.

• Separate the cable from the phone case.

Remove the USB-C port from its recess.

Do not strain the flex cable or damage the charging assembly.

The antenna board remains attached to the phone case.

Slowly slide the spudger under the antenna board.

• Lift the edge of the board using the spudger, separating the adhesive tape.
• Pry slowly and carefully to avoid strain on the board.

Lift the charging assembly out of the phone case.