iPhone 6s Plus iSight Camera Replacement

• To prevent potential hazards and damage, ensure the battery's charge level is reduced to less than 25% prior to beginning the disassembly process.A lithium-ion battery must be fully charged.Accidental puncture presents a fire and/or explosion hazard.
• Ensure the iPhone is completely de-energized by turning it off prior to starting the teardown process.
• Using a Pentalobe screwdriver, detach the two screws, each measuring 3.4 mm, located on both sides of the Lightning connector.

• To simplify the opening process, the following two steps utilize the Anti-Clamp tool, a custom-designed aid; if you do not have this tool, proceed to the instructions three steps further down.
• Refer to the included guide for detailed procedures regarding the Anti-Clamp's operation.
• To release the Anti-Clamp's arms, move the blue handle in a rearward direction.
• Position the arms so they extend across the iPhone's left or right side.
• Affix suction cups to the iPhone's front and rear surfaces, placing them close to the lower edge, directly above the home button.
• Apply vacuum to the targeted surface by pressing the cups firmly against each other.
• To improve the Anti-Clamp's adherence if the iPhone's exterior feels excessively smooth, apply adhesive tape to the device's surface.

• Moving the blue handle in a forward direction will engage the locking mechanism for the arms.
• Rotate the handle fully, completing a 360-degree turn, observing for the initial signs of cup expansion.
• Maintain parallel positioning of the suction cups; should misalignment occur, gently release the suction cups' hold and reposition the arms.
• Once sufficient separation is achieved by the Anti-Clamp tool, slide a prying tool beneath the display.
• To ensure adequate clearance, adjust the handle position by 90 degrees.
• To prevent damage, rotate the component no more than 90 degrees at each step, pausing briefly between rotations to allow the Anti-Clamp device to function and the necessary settling time to occur.

• Lacking an Anti-Clamp tool, proceed with the subsequent three steps to utilize a suction handle.
• Using a heat source like an iOpener or hair dryer, gently warm the bottom perimeter of the iPhone's casing for approximately 60 seconds.
• Applying heat will loosen the adhesive that holds the display in place, facilitating separation.

• Removing the 6s Plus display will release a perimeter adhesive strip; replacement adhesive strips should be prepared beforehand if desired. Functionality remains unaffected whether the adhesive is replaced or not.
• Using a suction cup, secure its surface to the display assembly's lower left corner.
• To facilitate suction cup attachment when the display has severe cracking, apply a sheet of clear packing tape across the damaged area; as an alternative, a robust adhesive tape can be substituted for the suction cup. Should these methods prove ineffective, secure the suction cup directly to the fractured screen using superglue.

• Apply steady, even force to lift the suction cup, generating a small separation between the front panel and the rear case.
• To avoid display assembly damage, use minimal force when separating it from the rear case; the goal is to establish a narrow separation.

• To avoid damage, begin separating the front panel by gently levering it away from the chassis at the indentation located directly over the headphone jack.
• Carefully hold the suction cup firmly in place, then use the spudger's flat tip to access the separation between components, positioning it directly over the headphone jack.

• Using a spudger, gently increase the separation between the front panel and rear case.

• Using a screwdriver with a flat head, carefully slide the tip into the slot.Use a plastic pry tool, often referred to as a spudger.Locate the component along the display's right side.
• Carefully move theUse a plastic pry tool, often referred to as a spudger, to carefully separate components.Raise the component along the right-hand vertical plane.

• Employ a 3/8-inch socket wrench to loosen the retaining bolt, ensuring you maintain a firm grip and avoid over-tightening during reassembly, as excessive force can damage the threaded insert.Use a plastic pry tool.Maintain pressure on the rear case with your fingers while lifting the suction cup to release the phone.
• Carefully detach the display from its mounting points, but leave it connected to the system, avoiding complete removal.Carefully avoid stressing the display's upper edge, as doing so risks harming the data cables located there.

• Employing a careful grip on the display assembly, raise it to separate the phone, utilizing the front panel's top clips as a pivot point.
• Carefully separate the display assembly from the device housing, creating a gap of approximately 1 millimeter.Rotate to a 90-degree angle.Position the device at an angle, securing it in place with support to prevent movement during the repair process.
• To prevent damage, limit display exposure during the repair process.Rotate to a 90-degree angle.Care must be taken as the display, digitizer, and front camera cables remain attached to the phone's upper section and are susceptible to damage if pulled forcefully.
• To avoid stressing the display's wiring during the repair process, secure it with a rubber band.
• As a temporary measure, an unopened standard-sized canned drink can provide the necessary support for the display.

• Detach two.Use a Phillips head screwdriver.Fasten the battery connector bracket to the logic board, ensuring the screws are tightened to the specified lengths.
• Begin the process by executing the singular action.Use a screw with a diameter of 2.9 millimeters.
• Begin the process by executing the action designated as "One."Use a 2.3-millimeter screw.

To prevent irreversible damage, meticulously organize and document the location of every screw throughout this repair process, ensuring correct placement during reassembly.

Employ a 3/8-inch socket wrench to loosen the retaining bolt, ensuring you maintain a firm grip and wear safety glasses to protect against potential debris.Use a plastic pry tool to gently separate.Use a clean fingernail or similar tool to detach the battery connector from the logic board, ensuring it is lifted vertically.

To prevent unintended activation, carefully reshape the connector and then test the iPhone's power functionality during the repair process.

• Detach the listed components.Use a Phillips head screwdriver.:
  
  • Three.Utilize fasteners with a diameter of 1.3 millimeters.
  • Begin the process with the number one.Use a screw with a diameter of 1.6 millimeters.
  • Begin the process by executing the action designated as "One."Use a 3.0 mm screw.
• Ensure proper installation of this component during reassembly.A screw with a diameter of 3.0 millimeters.Position the component precisely in the bracket's upper-right quadrant to prevent logic board damage.

Using a T4 Torx screwdriver, detach the bracket securing the display cable.

• Avoid applying force to the logic board socket while releasing the connector; focus solely on the connector's release mechanism.
• Employ a 3/8-inch socket wrench to loosen the retaining bolt, ensuring you apply consistent pressure to avoid damaging the threaded insert; torque the bolt to 18 Nm upon reinstallation, and be aware that the spring clip is easily dislodged during this process.Use a plastic pry tool.Carefully detach the connector securing the front camera and its associated sensor cable.

• Employ a 3/8-inch socket wrench to loosen the fastener, ensuring you apply consistent pressure to avoid damaging the retaining clip and observe the torque specification of 12 Nm, as indicated in the service manual, and wear safety glasses to protect your eyes.Use a plastic pry tool.Carefully separate the digitizer cable from its connection on the logic board by applying upward pressure.
• To ensure proper alignment and prevent damage, avoid applying pressure to the connector's middle when reattaching the digitizer cable; instead, gently secure it by pressing on one end, then the other. Central pressure risks warping the component.The display's touch functionality is impaired due to damage to the digitizer..

• Prior to either detaching or reattaching the cable in this procedure, ensure the battery is disconnected.
• Carefully lift the home button/fingerprint sensor cable connector directly upward from its position on the logic board.

• Carefully detach the display assembly, ensuring no damage occurs.
• If you're replacing the adhesive securing the display's perimeter, stop at this point during reassembly.

• Using a Phillips screwdriver, detach the screws located above the camera bracket.
  • A single screw with a 1.9 mm diameter is required.
  • A screw with a 2.4-millimeter head diameter is required.

• Carefully detach the iSight camera connector from the socket located on the logic board.
  Carefully lift the connector, ensuring the socket remains securely attached to the logic board.

• Using the tool's straight edge, carefully slide it into the designated space.Use a plastic pry tool, often referred to as a spudger, to gently separate components.Using appropriate tools, position the component within the specified gap.The integrated camera module is referred to as the iSight.Carefully remove the rear casing.
• Using a prying tool, carefully separate the component.The integrated camera module is referred to as the iSight.Carefully extract the component from its enclosure.